Search results for: hdmi
HDMI 4K over IP PoE Receiver
Finally get the 4K video wall display you have always wanted with this HDMI 4K over IP solution which allows HDMI equipment supporting up to 4K @ 30Hz or 1080p at 60Hz resolution to be connected and extended to create a video wall of user-configurable size (X by Y) supporting 100’s of screens, depending on network bandwidth, utilizing one Receiver for each display in the array.
Transmitter (500759-TX) and Receiver (500759-RX) can be connected via Cat5e/6 cable up to 330ft (100m) from an Ethernet Switch. The Transmitters and Receivers support PoE (PD) and may be powered by a PoE (PSE) Ethernet Switch. The IR Emitter and IR Sensor, if required, may be purchased separately for IR based remote control applications. Look no further for video over IP solutions.
The MuxLab Pro Digital Network Controller (500812) is available to simplify configuration and control and allows for third-party smartphone and tablet management.
Note: This device supports PoE (PD), and is intended to be powered via a PoE (PSE) Ethernet Switch. If a PoE (PSE) Ethernet Switch is unavailable, then the power supply (500993) may be purchased separately.
IMPORTANT NOTE
A new firmware version 2.0 has been released, which includes important enhancements such as support for infrared Pronto codes, numerous bug fixes,ÿimproved system performance, and support for the new models including the 500778 & 500777-RX. Please see the Release Notes for further details.
Firmware version 2.0 or greater for this device will only operate correctly with compatible devices that are also running the same firmware version 2.0 or greater.ÿIf your existing installation includes compatible devices with older firmware versions, you have two options:
- Either upgrade all your existing compatible devices to firmware version 2.0 or greater.
- Or downgrade the new device to a firmware version lower than 2.0.
Firmware versions for your compatible devices are available at the following MuxLab website link: https://muxlab.com/support?section=software-and-firmware
Read MoreHDMI 4-Play Extender, UHD-4K, TX
The HDMI 4-Play Extender Kit allows HDMI equipment to be connected up to 330 ft (100 m) @ 1080p Deep Color via one Cat 5e/6 unshielded twisted pair cables in a point-to-point configuration. The product also features one LAN port for interconnecting Ethernet equipment and a RS-232 port for control via the same Cat5e/6 cable. The kit comes with one Transmitter and one Receiver as well as an IR Emitter and IR Sensor for remote control applications.
Applications:
- Commercial and residential audio systems
- Boardroom systems
- Collaborative PC systems
- Medical information systems
HDMI 4-Play Extender Kit
ÿThe HDMI 4-Play Extender Kit allows HDMI equipment to be connected up to 330 ft (100 m) @ 1080p Deep Color via one Cat 5e/6 unshielded twisted pair cables in a point-to-point configuration. The product also features one LAN port for interconnecting Ethernet equipment and a RS-232 port for control via the same Cat5e/6 cable. The kit comes with one Transmitter and one Receiver as well as an IR Emitter and IR Sensor for remote control applications.ÿ
Applications:ÿ
Commercial and residential audio systems, boardroom systems, collaborative PC systems, and medical information systems.ÿ
Read MoreHDMI 4K over IP PoE Transmitter
Finally get the 4Kÿvideo wall display you have always wanted with this HDMI 4K over IP solutionÿwhich allows HDMI equipment supporting up to 4K @ 30Hz or 1080p at 60Hz resolution to be connected and extended to create a video wall of user-configurable size (X by Y) supporting 100’s of screens, depending on network bandwidth, utilizing one Receiver for each display in the array.
Transmitter (500759-TX) and Receiver (500759-RX) can be connected via Cat5e/6 cable up to 330ft (100m) from an Ethernet Switch.ÿThe Transmitters and Receivers support PoE (PD) and may be powered by a PoE (PSE) Ethernet Switch. The IR Emitter and IR Sensor, if required, may be purchased separately for IR based remote control applications.
The Pro Digital Network Controller (500812) is available to simplify configuration and control and allows for third-party smartphone and tablet management.
Note: This device supports PoE (PD), and is intended to be powered via a PoE (PSE) Ethernet Switch. If a PoE (PSE) Ethernet Switch is unavailable, then the power supply (500993) may be purchased separately.
IMPORTANT NOTE
A new firmware version 2.0 has been released, which includes important enhancements such as support for infrared Pronto codes, numerous bug fixes, improved system performance, and support for the new models including the 500778 & 500777-RX. Please see the Release Notes for further details.
Firmware version 2.0 or greater for this device will only operate correctly with compatible devices that are also running the same firmware version 2.0 or greater. If your existing installation includes compatible devices with older firmware versions, you have two options:
- Either upgrade all your existing compatible devices to firmware version 2.0 or greater.
- Or downgrade the new device to a firmware version lower than 2.0.
Firmware versions for your compatible devices are available at the following MuxLab website link: https://muxlab.com/support?section=software-and-firmware
Read More4×2 HDMI 2.0 Quad-View Processor, US
The 4×2 HDMI 2.0 Quad-View Processor allows up to four (4) HDMI 4K/60 sources to be simultaneously presented on one or two displays at 4K/60 as a multi-view arrangement. The user may select from one of five (5) default multi-view layout presets, or from eight (8) custom layout presets (resized and position as required with PIP support) in order to tailor their multi-view setup.
The unit supports transitions including seamless, fade-in & fade-out, wipe, and dissolve when switching in full screen mode. Pass through of all audio formats is supported, including 2CH audio extraction via two RCA jacks. The user may provide a background and logo to be displayed.
The unit may be managed locally via front panel push buttons or remotely via IR (IR Remote is included), RS232 and over an Ethernet network, and comes with rackmount brackets for a 19” rack, and a 12VDC @ 5A Power Supply.
Applications:
Digital Signage, Security & Surveillance systems, education, conference rooms, presentation halls, and test lab environments
Read MoreMuxLab Premiers New HDMI 2.0 over IP Solution at ISE Supporting 4K/60
Debuting at ISE this year is the MuxLab HDMI 2.0 over IP PoE Extender, 4K/60 (model 500779). This unique transceiver may be configured to operate as a transmitter or receiver to deliver HDMI at up to 4K (3840×2160) @60Hz (4:4:4) via a 1Gbps Ethernet Switch. AV can be delivered in one-to-one, one-to-many and many-to-many configurations…
Read MoreHDMI/VGA/USB over IP PoE Wall Plate Transmitter, UHD-4K
The HDMI/VGA/USB over IP PoE Wall Plate Transmitter allows HDMI, VGA and USB equipment to be connected up to 330ft (100m), with video supported at up to 4K (3840×2160) resolution @ 30Hz via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. The USB port may be used for extending various USB devices including Smart Boards. Point-to-multipoint and multipoint-to-multipoint configurations are also possible by connecting several Transmitters and Receivers to the same local Ethernet IP network via an Ethernet Switch. The HDMI/VGA/USB over IP PoE Wall Plate Transmitter also supports PoE (PD) if used with a PoE (PSE) Ethernet Switch. Additional Transmitters may be purchased separately depending on the intended application and number of units required.
For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet Switch must have Gigabit ports, Jumbo Frame capability, DHCP Server capability, PoE, and additionally support the IGMP communication protocol for the multipoint-to-multipoint case. MuxLab recommends using the Cisco SG300 or SG500 Series Managed Switches.
The MuxLab ProDigital Network Controller is available to simplify the configuration and utilization of the 500777-TX and other MuxLab IP based products via an Ethernet web interface. The MuxLab Control Android and iOS Application may also be used for connectivity management, in combination with the Network Controller.
Applications
Applications include commercial and residential AV systems, classroom systems, digital signage, boardroom systems, conference rooms, and collaborative PC systems.
IMPORTANT NOTE!
A new firmware version 2.0 has been released, which includes important enhancements such as support for infrared Pronto codes, numerous bug fixes, improved system performance, and support for the new models including the 500778 & 500777-RX. Please see the Release Notes for further details.
Firmware version 2.0 or greater for this device will only operate correctly with compatible devices that are also running the same firmware version 2.0 or greater. If your existing installation includes compatible devices with older firmware versions, you have two options:
- Either upgrade all your existing compatible devices to firmware version 2.0 or greater.
- Or downgrade the new device to a firmware version lower than 2.0.
Compatible devices include the following TX and RX models:ÿ500758, 500759, 500770, 500771, 500773, 500777, 500778.
KVM HDMI over IP PoE Transmitter
The USB KVM Extender over IP PoE allows HDMI & USB equipment to be connected up to 330ft (100m) over an Ethernet LAN, supporting 1920×1200 and 1080p resolution @ 60Hz via Cat5e/6 cable in multiple point-to-point and point-to-multipoint configurations. The Transmitter (500770-TX) and Receiver (500770-RX) support PoE (PD) if used with a PoE (PSE) Ethernet Switch.
The Transmitter terminates to a computer server/workstation via an HDMI & USB port, The Receiver terminates to an HDMI display and up to 4 USB devices such as a keyboard, mouse, printer, drawing pad, storage device, etc., via a 4 port USB hub. A single Receiver can be switched via hotkey sequences to any Transmitter on the network, allowing a single operator to manage numerous servers/workstations, in a distributed KVM application.
Applications:
- Management of multi-server systems supporting HDMI displays in IT departments within corporations
- Educational institutions
- CAD Design
- Graphic Design
- Media Servers
- Data Centers
IMPORTANT NOTE!
A new firmware version 2.0 has been released, which includes important enhancements such as support for infrared Pronto codes, numerous bug fixes, improved system performance, and support for the new models including the 500778 & 500777-RX. Please see the Release Notes for further details.
Firmware version 2.0 or greater for this device will only operate correctly with compatible devices that are also running the same firmware version 2.0 or greater. If your existing installation includes compatible devices with older firmware versions, you have two options:
- Either upgrade all your existing compatible devices to firmware version 2.0 or greater.
- Or downgrade the new device to a firmware version lower than 2.0.
HDMI/USB over IP PoE Wall Plate Receiver, UHD- 4K (White)
The HDMI/USB over IP PoE Wall Plate Receiver, UHD- 4K installs in a double-gang wall box to provide a convenient interface for HDMI display equipment and USB connectivity to manage Smart White Boards and other USB based devices. The unit has one (1) HDMI- Out, one (1) Audio-Out, two (2) USB 2.0 Type-A ports, two (2) USB 1.1 type-A ports, and one Ethernet Port. It supports video up to 4K @ 30Hz (4:4:4) and 4K @ 60Hz (4:2:0). The HDMI/USB over IP PoE Wall Plate Receiver, UHD-4K allows HDMI and USB equipment to be extended up to 330ft (100m). The unit supports an RS232 port plus a Directional IR port to manage remote devices. The device may be powered via a PoE enabled 1Gig Ethernet Switch.
Applications:
- Commercial and residential AV systems? K-6 and K-12 classroom AV systems
- Digital signage
- Boardroom systems
- Collaborative PC systems
- Medical information systems
IMPORTANT NOTE!
A new firmware version 2.0 has been released, which includes important enhancements such as support for infrared Pronto codes, numerous bug fixes, improved system performance, and support for the new models including the 500778 & 500777-RX. Please see the Release Notes for further details.
Firmware version 2.0 or greater for this device will only operate correctly with compatible devices that are also running the same firmware version 2.0 or greater. If your existing installation includes compatible devices with older firmware versions, you have two options:
- Either upgrade all your existing compatible devices to firmware version 2.0 or greater.
- Or downgrade the new device to a firmware version lower than 2.0.
Firmware versions for your compatible devices are available at the following MuxLab website link: https://muxlab.com/support?section=software-and-firmware
Compatible devices include the following TX and RX models: 500758, 500759, 500770, 500771, 500773, 500777, 500778.
HDMI/VGA/USB over IP PoE Wall Plate Transmitter, UHD-4K (White)
The HDMI/VGA/USB over IP PoE Wall Plate Transmitter allows HDMI, VGA and USB equipment to be connected up to 330ft (100m), with video supported at up to 4K (3840×2160) resolution @ 30Hz via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. The USB port may be used for extending various USB devices including Smart Boards. Point-to-multipoint and multipoint-to-multipoint configurations are also possible by connecting several Transmitters and Receivers to the same local Ethernet IP network via an Ethernet Switch. The HDMI/VGA/USB over IP PoE Wall Plate Transmitter also supports PoE (PD) if used with a PoE (PSE) Ethernet Switch. Additional Transmitters may be purchased separately depending on the intended application and number of units required.
For the point-to-multipoint and multipoint-to-multipoint configuration the Ethernet Switch must have Gigabit ports, Jumbo Frame capability, DHCP Server capability, PoE, and additionally support the IGMP communication protocol for the multipoint-to-multipoint case. MuxLab recommends using the Cisco SG300 or SG500 Series Managed Switches.
The MuxLab ProDigital Network Controller (500811) is available to simplify the configuration and utilization of the 500777-TX and other MuxLab IP based products via an Ethernet web interface. The MuxLab Control Android and iOS Application may also be used for connectivity management, in combination with the 500811 Network Controller.
Applications
Applications include commercial and residential AV systems, classroom systems, digital signage, boardroom systems, conference rooms, and collaborative PC systems.
IMPORTANT NOTE!
A new firmware version 2.0 has been released, which includes important enhancements such as support for infrared Pronto codes, numerous bug fixes, improved system performance, and support for the new models including the 500778 & 500777-RX. Please see the Release Notes for further details.
Firmware version 2.0 or greater for this device will only operate correctly with compatible devices that are also running the same firmware version 2.0 or greater.If your existing installation includes compatible devices with older firmware versions, you have two options:
- Either upgrade all your existing compatible devices to firmware version 2.0 or greater.
- Or downgrade the new device to a firmware version lower than 2.0.
Firmware versions for your compatible devices are available at the following MuxLab website link: https://muxlab.com/support?section=software-and-firmware
Compatible devices include the following TX and RX models:ÿ500758, 500759, 500770, 500771, 500773, 500777, 500778.